4x4 XLR Dante® Audio Bridge, Mic/Line Inputs with +48V, 8-Band PEQ, Delay, Redundant PoE+, 1U Rack
Level-Match, EQ and Time-Align at the Bridge - 8-Band PEQ on Every Input and Output, up to 50ms Output Delay, 6 Input Sensitivities

Brings four analog sources onto a Dante® network and sends four Dante® feeds back out to analog, with level matching, EQ and time alignment handled in the bridge itself. AUD-DTE-4X4XLR is a 1U, 19-inch metal rack unit. It has four XLR/TRS combo mic/line inputs, each with switchable +48V phantom power, and four balanced XLR line outputs.
A global line-up setting chooses one of six input sensitivities, from -35dBV for microphones to +24dBu for hot console outputs, and one of five output levels, from +20dBu to -18dBV. The same unit can take condenser mics and wireless receivers and drive professional or consumer-level destinations. Every input and output has an 8-band parametric EQ (+/-15dB) with parametric, shelf and pass filters, and every output has up to 50ms of delay. Five presets store complete room setups. The unit is configured from its built-in Web GUI or from Dante® Controller, supports AES67, and accepts ASCII commands over TCP/IP and Telnet from a control system. It has primary and secondary Dante® ports, and both can take PoE+. If the primary network fails, audio switches to the secondary network automatically, and either port can power the unit on its own.
- Four balanced analog inputs on XLR/TRS combo connectors, female
- Four balanced analog outputs on XLR, male
- Dante® 4x4 and AES67 audio input and output
- Primary and secondary Dante® ports on locking RJ45 connectors, both PoE+ (Class 4, IEEE 802.3at); audio switches to the secondary network automatically if the primary fails, and either port can power the unit on its own
- Gigabit (1000M) Dante® network connection over CAT6/6A/7, up to 328ft (100m) to the switch
- Accepts and delivers balanced or unbalanced analog audio
- +48V phantom power on each input, switched on or off per input, with a rear-panel indicator for each input
- Adjustable global 0dBFS line-up selection:
- Six input sensitivity levels: -35dBV, -18dBV, 0dBV, +4dBu, +14dBu, +24dBu
- Five output levels: +20dBu, +14dBu, +4dBu, 0dBV, -18dBV
- Built-in audio DSP for sensitivity gain, 8-band PEQ and delay control
- 8-band PEQ (+/-15dB) on every input and output, with Parametric, Lowpass, Highpass, Low Shelf and High Shelf filter types; stereo linking of input and output pairs; copy, import and export of PEQ settings
- Up to 50ms of delay on every output
- Dante® audio at 44.1kHz, 48kHz, 88.2kHz and 96kHz sampling rates, 16- or 24-bit
- Five preset scenes for saving and recalling complete setups
- Set up from the built-in Web GUI, with separate Admin and User accounts, or from Dante® Controller
- ASCII API control over TCP/IP (default port 8000) and Telnet (default port 23)
- DHCP or static IP addressing, set separately for the primary and secondary networks
- Firmware updates and configuration export and import from the Web GUI
- 12V DC locking power input (max 2.5A) and GND terminal
- Standard 1U 19-inch rack-mount metal chassis
- Works with RelayAV, KanexPro's control app: master volume and mute, each output's volume, mute, delay and level, each input's gain, mute, sensitivity and 48 V phantom power, input and output EQ, presets, auto standby and power, from the RelayAV app
| Audio | |
| Dante® Audio | Dante®/AES67 digital audio in/out; 44.1kHz, 48kHz, 88.2kHz, 96kHz; 16/24-bit |
| Analog Inputs | 4x mic/line, balanced/unbalanced |
| Analog Outputs | 4x line, balanced/unbalanced |
| Input Sensitivity | -35dBV, -18dBV, 0dBV, +4dBu, +14dBu, +24dBu |
| Output Level | +20dBu, +14dBu, +4dBu, 0dBV, -18dBV |
| Input Level | Max 24dBu (12.28Vrms), balanced line audio Max 18dBu (6.14Vrms), unbalanced line audio Min -35dBV (17.78mVrms), balanced mic audio |
| Input Impedance | 20k Ohm balanced 10k Ohm unbalanced |
| Output Level (Max) | 20dBu (7.75Vrms), balanced audio 14dBu (3.875Vrms), unbalanced audio |
| Output Impedance | 600 Ohm balanced 300 Ohm unbalanced |
| Phantom Power | +48V on each input, switchable per input |
| THD+N | < 0.01% at +4dBu, 1kHz |
| S/N Ratio | at least 105dB at +4dBu, 1kHz, A-weighted |
| Dynamic Range | at least 105dB at +4dBu, 1kHz, A-weighted |
| Frequency Response | 20Hz to 20kHz (+/-0.5dB) |
| DSP | |
| Parametric EQ | 8 bands on every input and output; +/-15dB gain; 20Hz to 20kHz; Q 0.02 to 16 |
| Filter Types | Parametric, Lowpass, Highpass, Low Shelf, High Shelf |
| Input Gain | -12dB to +12dB, 0.1dB steps |
| Output Delay | 0 to 50ms per output |
| Presets | 5 user presets |
| Connections | |
| Mic/Line Inputs | 4x XLR/TRS combo, female |
| Line Outputs | 4x XLR, male |
| Dante® Primary | 1x RJ45 locking connector, PoE+/PD (Class 4, IEEE 802.3at) |
| Dante® Secondary | 1x RJ45 locking connector, PoE+/PD (Class 4, IEEE 802.3at) |
| Power | 1x 12V DC, 2-pin locking jack, max 2.5A |
| Ground | 1x GND terminal |
| XLR Pinout | Pin 1: Ground/Shield; Pin 2: Positive/Hot; Pin 3: Negative/Cold |
| Network and Control | |
| Network Bandwidth | Dante® network, 1000M |
| Transmission Distance | 328 ft (100 m) over CAT6/6A/7 |
| Control | Built-in Web GUI, Dante® Controller, TCP/IP and Telnet ASCII API; RelayAV |
| Default Ports | TCP/IP: 8000; Telnet: 23 (both configurable) |
| IP Addressing | DHCP (default) or static, set per network |
| Indicators and Buttons | |
| Front Panel | POWER LED, STATUS LED, RESET button |
| Rear Panel | 4x green 48V phantom power indicators, one per input |
| Power | |
| Power Supply | 12V/2.5A 2-pin locking power supply, or PoE+/PD (Class 4, IEEE 802.3at) |
| Power Consumption | 10.2W max |
| Physical | |
| Housing | Metal enclosure |
| Color | Black |
| Form Factor | Standard 1U 19-inch rack-mount |
| Dimensions (W x D x H) | 17.32 x 7.87 x 1.73 in (440 x 200 x 44 mm) |
| Weight | 4.72 lbs (2.14 kg) |
| Environmental | |
| Operating Temperature | 32°F to 104°F (0°C to 40°C) |
| Storage Temperature | -4°F to 140°F (-20°C to 60°C) |
| Operating Humidity | 20% to 80% RH, non-condensing |
| Storage Humidity | 10% to 90% RH, non-condensing |
| ESD Protection | IEC 61000-4-2: +/-8kV (air-gap discharge), +/-4kV (contact discharge) |
| Package Contents | |
| 1x | AUD-DTE-4X4XLR 4x4 XLR Dante® Audio Bridge |
| 1x | 12V/2.5A locking power supply with multinational plug adapters |
| 2x | Rack-mounting ears |
| 8x | Machine screws |
Which Dante sample rates and bit depths does the AUD-DTE-4X4XLR support?
What input sensitivity settings and maximum input levels does it accept?
Does it work with AES67 devices?
What does a typical system with it look like?
What does the network switch and cabling need to provide?
Which XLR connectors does it use, and how are they wired?
A condenser microphone gives no signal. What should I check?
The POWER LED is red or the STATUS LED is flashing. What does that mean?
Does it show up in Dante Controller like any other Dante device?
Will it take microphones directly, or do I need separate preamps?
Ask Claude, ChatGPT or Copilot about the AUD-DTE-4X4XLR: its specifications, your price, stock, and a draft order for you to place. Or wire the REST API into your quoting tool or ERP.




